AcQ Inducom Products

Homepage AcQ

• The M213 provides GPS timing in a single-wide M-Module format adhering to the ANSI/VITA 12-1996 specification for M-Modules
• The M213 may be installed on any carrier board supporting the M-Module specification
• Carriers are available that allow the M213 to be used in VXI, VME, PCI, cPCI and many other system architectures
• M213 product

• 68332 local 32-bit microcontroller with up to 1 Mbyte memory, of which 128 kbyte is dual ported
• Optional onboard Flash memory up to 4 Mbit
• Jumper selectable boot device (RAM or EPROM)
• 16 buffered TPU channels
• 4 general purpose buffered I/O channels
• All TPU channels and buffered I/O lines have individual programmable direction
• Onboard firmware is extendable
• M312 product

• CompactFlash(CF) and CompactFlash+ (CF+) compatible
• Type I and type II card compatible
• Microdrive (tm) compatible
• Low voltage support, 3.3V or 5V cards
• Hot socketing for CompactFlash cards
• Card accessible through frontpanel
• Host controller configurable for memory mode or I/O mode
• Two individually configurable windows for accessing the CompactFlash card
• 3U form factor
• Host interrupts supported
• CPCI340 product

• CompactFlash (CF) and CompactFlash+ (CF+) compatible
• Type I and Type II card compatible
• Microdrive (tm) compatible
• Low voltage support, 3.3v or 5v cards
• Hot socketing
• Card accessible through frontpanel
• Host Controller configurable for memory mode or I/O mode
• Two individuallly configurable windows for accessing the CompactFlash card
• A08/D16 M-module interface
• Host interrupts supported
• Identification EEPROM
• M340 product

• CompactFlash(CF) and CompactFlash+ (CF+) compatible
• Type I and type II card compatible
• MicrodriveTM compatible
• Low voltage support, 3.3V or 5V cards
• Hot socketing for CompactFlash cards
• Card accessible through frontpanel
• Host controller configurable for memory mode or I/O mode
• Two individually configurable windows for accessing the CompactFlash card
• 3U form factor
• Host interrupts supported
• VME1340 product

• AD598 integrated LVDT signal conditioner for each LVDT channel
• Wide range adjustable LVDT excitation frequency and amplitude
• Interfaces with 4/5/6-wire LVDT/RVDT devices
• Distance between LVDT/RVDT devices and M372 can be up to 100 meters
• LM12458 Integrated Data Acquisition System with 13-bit resolution and sequencer
• Programmable conversion rate, resolution, number of conversions and comparison limits
• Interrupt on numerous programmable events (i.e. sequence completion, limit crossing)
• Operates with minimum CPU intervention after initialization
• M372 product

• Two timer/counter inputs
• Programmable AC/DC coupling
• Input voltage range +/- 10V
• Additional inputs +/- 300V
• Front-end optically isolated
• Programmable trigger level and sensitivity
• Minimum pulse width of the counter signals of 20 nanoseconds
• 32-bit counter and 32-bit timer with 100 MHz timebase
• CPCI385 product

• Bandwidth of 250MHz (M385/100M: 100MHz)
• Timer/counter with two input signals
• Input voltage range of 10V pk-pk
• Optical isolation
• Programmable input conditioning
• 32-bit timer with 200MHz (M385/100M: 100MHz) timebase
• 32-bit counter
• A08D16 M-module interface
• INTA software-end-of-interrupt
• EEPROM for module ID and calibration data
• Extensive software support: APIS based, LabView and LabWindows CVI
• M385 product

• Two timer/counter inputs
• Programmable AC/DC coupling
• Input voltage range +/- 10V
• Additional inputs +/- 300V
• Front-end optically isolated
• Programmable trigger level and sensitivity
• Minimum pulse width of the counter signals of 20 nanoseconds
• 32-bit counter and 32-bit timer with 100 MHz timebase
• PCI385 product

• Eight timer/counter inputs
• Programmable AC/DC coupling
• Input voltage range +/- 10V
• Additional inputs +/- 300V
• Front-end optically isolated
• Programmable trigger level and sensitivity
• Minimum pulse width of the counter signals of 20 nanoseconds
• 32-bit counter and 32-bit timer with 100 MHz timebase
• VME385 product

• Sigma/Delta ADC with 16-bit resolution
• PT100 linearization (IEC751-1983, DIN43760-1980, JIS C1604-1989)
• Programmable minimum/maximum value alarms
• Auto calibration
• No potentiometers
• Analog front-end is optically isolated
• On-board DC/DC converter for isolated power supply
• Data acquisition handled by TMS320C203 DSP, transparent for user
• Measurement range: -200°C .. +850°C
• Excitation current: 1mA
• CPCI390 product

• Supports PT100, PT200, PT500 or PT1000 sensors
• Supports two-, three-, and four wire RTD devices
• Internal 16-bit measurement
• PT100 linearization (IEC751-1983, DIN43760-1980, JIS C1604-1989)
• Programmable min/max alarms
• Autocalibrating, no potentiometers
• Optical isolation
• Measurement Range: -2000C to +8500C
• Update rate up to 7.5Hz
• Identification EEPROM
• M390 product

• Sigma/Delta ADC with 16-bit resolution
• PT100 linearization (IEC751-1983, DIN43760-1980, JIS C1604-1989)
• Programmable minimum/maximum value alarms
• Auto calibration
• No potentiometers
• Analog front-end is optically isolated
• On-board DC/DC converter for isolated power supply
• Data acquisition handled by TMS320C203 DSP, transparent for user
• Measurement values continuously updated in dual-ported SRAM
• Up to 7.5Hz output update rate
• PCI9050 Controller by PLX (PCI 2.1compliant)
• Measurement range: -200°C .. +850°C
• PCI390 product

• These modules give the user the opportunity to make audio connections via the rear I/O of the PMC481 or ccPMC481 Audio Card
• PIM481-J/DSUB product

• Single PMC slot (IEEE 1386.1-2001) with front I/O and rear I/O
• Optional PIM481-J or PIM-DSUB (VITA 36) for rear I/O connections
• Crystal CS4281 CrystalClearTM PCI Audio Interface controller
• Crystal CS4299 CrystalClearTM SoundFusionTM Audio Codec '97
• PCI interface: PCI 2.1 compliant, 33MHz, 32-bit interface, 3.3V and 5.0V signalling supported, 5V and 12V supply
• 4 audio connections via front or optional PIM faceplate: Line In (stereo), Line Out (stereo), Microphone In (mono), Speaker Out (stereo)
• On-board amplifier
• PMC481 product

• Single PMC slot (IEEE 1386.1-2001) with front I/O and rear I/O
• Optional PIM481-J or PIM-DSUB (VITA 36) for rear I/O connections
• Crystal CS4281 CrystalClearTM PCI Audio Interface controller
• Crystal CS4299 CrystalClearTM SoundFusionTM Audio Codec '97
• PCI interface: PCI 2.1 compliant, 33MHz, 32-bit interface, 3.3V and 5.0V signalling supported, 5V and 12V supply
• 4 audio connections via front or optional PIM faceplate: Line In (stereo), Line Out (stereo), Microphone In (mono), Speaker Out (stereo)
• On-board amplifier
• ccPMC481 product